• Amused
  • Angry
  • Annoyed
  • Awesome
  • Bemused
  • Cocky
  • Cool
  • Crazy
  • Crying
  • Depressed
  • Down
  • Drunk
  • Embarrased
  • Enraged
  • Friendly
  • Geeky
  • Godly
  • Happy
  • Hateful
  • Hungry
  • Innocent
  • Meh
  • Piratey
  • Poorly
  • Sad
  • Secret
  • Shy
  • Sneaky
  • Tired
  • Page 1 of 2 12 LastLast
    Results 1 to 20 of 29

    Thread: How To Install A Bottom Drain

    1. #1
      birdman's Avatar
      birdman is offline DIY Savant
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jun 2005
      Location
      Palm Springs, CA.
      Posts
      21,812

      Exclamation How To Install A Bottom Drain

      This Bottom Drain is being installed in an indoor plywood tank, but the procedure is the same for an outside concrete bedded Bottom Drain.

      Start by cutting the circle out of your liner to fit the BD.
      Attached Images Attached Images  

      • Remove Ads
        Advertising from Google
        Promoting Koi and Pond
        keeping since 2007

         

    2. #2
      birdman's Avatar
      birdman is offline DIY Savant
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jun 2005
      Location
      Palm Springs, CA.
      Posts
      21,812
      Next get some 2" finish nails and sharpen the point. Put these finish nails in every other hole, point up. This will space the liner up off the BD flange for easy adhesive application and are used as alignment pins for installing the clamping ring.
      Attached Images Attached Images   

    3. #3
      birdman's Avatar
      birdman is offline DIY Savant
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jun 2005
      Location
      Palm Springs, CA.
      Posts
      21,812
      Now apply a heavy bead of P&L polyurethane roof and flashing adhesive on the BD flange. Then push the liner down over the pointed nails.
      Attached Images Attached Images   

    4. #4
      birdman's Avatar
      birdman is offline DIY Savant
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jun 2005
      Location
      Palm Springs, CA.
      Posts
      21,812
      Next apply another bead of P&L on top of the liner and place the clamping ring on that, using the protruding nails as alignment pins. One by one remove a nail and put in a screw. Just tight enough to see some of the P&L squeeze out.
      Attached Images Attached Images   

    5. #5
      birdman's Avatar
      birdman is offline DIY Savant
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jun 2005
      Location
      Palm Springs, CA.
      Posts
      21,812
      Now go around and hand tighten the clamping ring. Not to tight, just enough to ooze the P&L out. if you go to tight you can crack the clamping ring or strip out the screw.
      Attached Images Attached Images  

    6. #6
      birdman's Avatar
      birdman is offline DIY Savant
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jun 2005
      Location
      Palm Springs, CA.
      Posts
      21,812
      Smooth out the P&L with a gloved finger. If you get any on you acetone will take it off.

      Finish off by installing the dome. In most cases you will have to trim the stand pipe.
      For a 3" BD flowing 15 to 2500 gph you want a half inch gap.
      For a 4" BD flowing 25 to 3500 gph you want a 5/8 to 3/4 inch gap.

      Nothing to it. I use the same procedure and alignment pins for doing TPR flanges.
      Attached Images Attached Images  

    7. #7
      Paultergeist is offline Senior Member
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Apr 2009
      Location
      San Diego, California
      Posts
      2,530
      Another fantastically useful post, Steve. I realize that this is not an extremely complicated process -- but seeing photos of it performed step-by-step, with all the useful narration and helpful hints, really makes it seem easy. Thanks very much for going to the trouble.

      Paul

    8. #8
      Sp00ks's Avatar
      Sp00ks is offline Senior Member
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jul 2009
      Location
      North Carolina
      Posts
      3,470
      Steve,

      Since you posted this and the fact that I'll be installing my liner this weekend, I have a couple of questions.

      My pond is an irregular shape.
      I already have the bottom drain concreted in and I laid the underlayment tonight.
      I am worried that I cut the liner, install the drain like described and start filling, the liner pulls and stresses that connection at the bottom drain.

      I would not be as worried if I had a square block pond. It would be easier to predict and lay the liner down. Since I am in a kidney shape with shelves etc. That the liner will pull when filled with water. I went what I think is overkill on the size of the liner and I'm probably just worried for nothing.....

      Any tips?
      Jerry

      Opportunity is missed by most people because it is dressed in overalls and looks like work.
      - Thomas A. Edison

    9. #9
      TheCrow1994 is offline Member
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jun 2007
      Location
      Omaha, NE
      Posts
      61
      Thanks for the post, Steve. Very informative pictures and descriptions.

    10. #10
      Hi Utsuri's Avatar
      Hi Utsuri is offline Senior Member
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jul 2009
      Location
      Oregon, USA
      Posts
      1,519
      Quote Originally Posted by Sp00ks View Post
      I am worried that I cut the liner, install the drain like described and start filling, the liner pulls and stresses that connection at the bottom drain.
      I am also installing an odd shaped pond. What I was thinking of doing was to provide a lot of slack liner along the top edge of the pond (sitting on the concrete collar). This way, when/if the liner tries to stretch and pull, it will take up the slack from the liner at the top, not at the bottom near the BD.

      • Remove Ads
        Advertising from Google
        Promoting Koi and Pond
        keeping since 2007

         

    11. #11
      Hi Utsuri's Avatar
      Hi Utsuri is offline Senior Member
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jul 2009
      Location
      Oregon, USA
      Posts
      1,519
      Great post Steve!

      The idea to use the nails as alignment pins really makes this an easy task.

      Two thumbs up... WAY UP!

    12. #12
      zack67360 is offline Senior Member
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Feb 2007
      Location
      Peru Kansas-SE KS.
      Posts
      967
      I too will be installing my liner hopefully next week. It makes me nervous to think about cutting holes in my liner, but your demonstration has answered some of the questions I had. I will have two bottom drains, and plan on leaving just a bit of slack in between the two BD, just in case it does want to pull.
      zack

    13. #13
      Hi Utsuri's Avatar
      Hi Utsuri is offline Senior Member
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jul 2009
      Location
      Oregon, USA
      Posts
      1,519
      Steve, if someone is going to also have an underlayment below the liner, that would go under the lip of the BD collar, right? Or, I suppose one could just trim the underlayment around the outside of the collar and leave it at that?

    14. #14
      birdman's Avatar
      birdman is offline DIY Savant
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jun 2005
      Location
      Palm Springs, CA.
      Posts
      21,812
      Quote Originally Posted by Hi Utsuri View Post
      I am also installing an odd shaped pond. What I was thinking of doing was to provide a lot of slack liner along the top edge of the pond (sitting on the concrete collar). This way, when/if the liner tries to stretch and pull, it will take up the slack from the liner at the top, not at the bottom near the BD.
      That's about it. You have to attach the BD before filling so just keep slack in the liner so it can settle from the sides.

    15. #15
      birdman's Avatar
      birdman is offline DIY Savant
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jun 2005
      Location
      Palm Springs, CA.
      Posts
      21,812
      Quote Originally Posted by Sp00ks View Post
      Steve,

      Since you posted this and the fact that I'll be installing my liner this weekend, I have a couple of questions.

      My pond is an irregular shape.
      I already have the bottom drain concreted in and I laid the underlayment tonight.
      I am worried that I cut the liner, install the drain like described and start filling, the liner pulls and stresses that connection at the bottom drain.

      I would not be as worried if I had a square block pond. It would be easier to predict and lay the liner down. Since I am in a kidney shape with shelves etc. That the liner will pull when filled with water. I went what I think is overkill on the size of the liner and I'm probably just worried for nothing.....

      Any tips?
      Yes you probably am. But we all do 1st time. Look at post 10 and 14.

    16. #16
      Noahsnana's Avatar
      Noahsnana is offline Koiphen Admin -
      is KPOTY 2024
       
      Feeling:
      ----
       
      Join Date
      Aug 2004
      Location
      So. MD
      Posts
      43,769
      Great thread Steve
      The will of God will not take you where the grace of God cannot keep you. .....
      "I contend that for a nation to try to tax itself into prosperity is like a man standing in a bucket and trying to lift himself up by the handle." -Winston Churchill Zone 7a
      I believe it can happen... Koi World Peace
      "The problem with socialism is that eventually you run out of other people's money." - Margaret Thatcher
      KPOTY 2024

    17. #17
      yorkie's Avatar
      yorkie is offline Supporting Member
      This user has no status.
       
      Feeling:
      Geeky
       
      Join Date
      Dec 2007
      Location
      Grand Rapids, MI
      Posts
      695
      Quote Originally Posted by Hi Utsuri View Post
      Steve, if someone is going to also have an underlayment below the liner, that would go under the lip of the BD collar, right? Or, I suppose one could just trim the underlayment around the outside of the collar and leave it at that?
      I tucked the liner under the lip of the bottom drain when I installed them in my pond. It seems to have worked well for me.

      Larry

    18. #18
      yorkie's Avatar
      yorkie is offline Supporting Member
      This user has no status.
       
      Feeling:
      Geeky
       
      Join Date
      Dec 2007
      Location
      Grand Rapids, MI
      Posts
      695
      Steve,

      I wish I would have seen this thread last year before I installed my 4 bottom drains it would have made lining up the screw holes much easier. But I must have done it right because they have been installed for a year and no leaks. A very helpful post for those installing a bottom drain. Thanks again Steve for all of the useful information that you post in this forum.

      Larry

    19. #19
      tarquin13 is offline Senior Member
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Jul 2009
      Location
      uk
      Posts
      508
      I so needed to see that, I have had to have thearpy over this proceedure and I have not even started my pond yet. ha ha

    20. #20
      phoman is offline Senior Member
      This user has no status.
       
      Feeling:
      ----
       
      Join Date
      Apr 2007
      Location
      chicago
      Posts
      150
      Great post. Thanks for sharing.

      • Remove Ads
        Advertising from Google
        Promoting Koi and Pond
        keeping since 2007

         

    Page 1 of 2 12 LastLast

    Posting Permissions

    • You may not post new threads
    • You may not post replies
    • You may not post attachments
    • You may not edit your posts
    •